ResinTech HPP100 High-Performance Polyaspartic — 2 Gal Kit
ResinTech HPP100 is a fast-curing aliphatic polyaspartic coating designed to be the exposed surface layer of ResinTech traffic and resin flooring assemblies. It combines UV stability, fast return to service, chemical resistance, and traffic-ready durability in one product.
HPP100 can be used clear or pigmented, indoors or outdoors. It may serve as a stand-alone topcoat on properly prepared concrete or as the final wear layer over compatible epoxy, broadcast, and decorative systems. Confirm coverage, recoat window, slip resistance, and substrate preparation against the current ResinTech TDS, SDS, and project specification before use.
A small-format kit of ResinTech HPP
HPP100 is the same fast-curing polyaspartic supplied in the ResinTech HPP contractor kit, packaged as a 2 US gal kit with one gallon of Part A and one gallon of Part B. The smaller format suits smaller floors, single garages, seal coats, and touch-up work.
For projects that need more material per mix, see the ResinTech HPP 10 L contractor kit.
A ResinTech alternative to Tremco Vulkem 951NF and Sika Sikalastic-394
ResinTech HPP100 is stocked in North Vancouver and used in the same UV-stable traffic-deck topcoat and finished wearing-surface applications. Product chemistry and complete system builds differ between manufacturers, so confirm suitability against the current ResinTech TDS before substituting.
Vulkem is a registered trademark of Tremco, and Sikalastic is a registered trademark of Sika. They are used here for identification and comparison only; no affiliation or endorsement is implied.
Product overview
| Field | Details |
|---|---|
| Brand | ResinTech |
| Product code | HPP100 |
| Product type | Two-component, high-solids aliphatic polyaspartic coating |
| Kit / pack size | 2 US gal kit — Part A 1 US gal (3.78 L) + Part B 1 US gal (3.78 L) |
| Mix ratio | 1:1 by weight (Part A : Part B) |
| Colour / finish | Clear or field-pigmented; light, medium, or heavy broadcast texture |
| System role | Primary UV-stable traffic surface, topcoat, seal coat, and traffic wear coat |
Where HPP100 sits in the system
HPP100 is the exposed, UV-stable finish of the ResinTech system. A typical assembly can prime and bond with CBE, build with TUE, and finish with HPP100 for a fast-curing, UV-stable surface.
For the most aggressive chemical and abrasion service, CRU is the premium topcoat upgrade. Where movement accommodation or waterproofing is required, a flexible base membrane such as FLEXCOAT-PU is used beneath the build. Confirm the complete system specification against current ResinTech documentation.
Best-use applications
Confirm every application against the current ResinTech HPP Technical Data Sheet before specifying.
- Single garages, small shops, entries, and smaller decorative floors where a full-size kit is more than needed
- Parking decks, drive aisles, parking stalls, and light-to-moderate vehicular traffic zones
- Balconies, podium decks, exterior walkways, corridors, and service areas
- Fast-track commercial, institutional, garage, and light industrial flooring
- Clear or pigmented seal coats over decorative flake, quartz, sand, or metallic epoxy floors
- UV-stable exposed topcoats over compatible ResinTech epoxy and reinforced broadcast layers
- Operating strata, parkade, and commercial projects where rapid return to service matters
- Weather-exposed concrete coating work where colour and gloss retention are important
Product data
Source: ResinTech HPP Technical Data Sheet (TDS-HPP-1.0). Values are typical at 23 °C and 50% relative humidity unless noted. Confirm all values against the current TDS before specifying or ordering.
| Property | Typical value | Note |
|---|---|---|
| Components | Two — Part A resin + Part B hardener | Mix only what can be placed within the working time |
| Mix ratio | 1:1 by weight | Part A : Part B |
| Solids content | 98% by weight | ASTM D1353 |
| Chemistry | High-solids aliphatic polyaspartic | UV-stable exposed-surface chemistry |
| Appearance | Clear or pigmented | Use compatible pigment or colorant where specified |
| Odour | Low to moderate | Ventilation is required during application and cure |
| Shelf life | 12 months | Unopened and stored properly at 10–30 °C |
Performance properties
These are typical values from the ResinTech HPP TDS. Actual results depend on the substrate, preparation, mixing, film build, and application conditions. Confirm all values against the current TDS.
| Property | Typical value | Test method / note |
|---|---|---|
| Bond strength to concrete | 310 psi | ASTM D4541; substrate typically controls the result |
| Tensile strength | 2,900 psi | ASTM D412 |
| Elongation | 20% | Flexible, traffic-capable film; not a crack-bridging membrane |
| Abrasion resistance | 30 mg loss (excellent) | ASTM D4060, CS-17 wheel, 1,000 g, 1,000 cycles |
| Shore hardness | 70 D | ASTM D2240 |
| Tack-free time | 1 hour | ASTM D1640 typical |
| Drying time | 4 hours at 15 mils | ASTM D1640, 24 °C / 50% RH |
| UV stability | Excellent | Suitable as an exposed interior or exterior top surface |
| Chemical resistance | Excellent | For the maximum chemical and abrasion upgrade, use CRU where specified |
| Return-to-service speed | Fast | Designed for rapid-turnaround flooring and traffic coating work |
Working time, recoat, and cure
Cool temperatures, high humidity, low airflow, and thicker films extend cure. Hot conditions shorten working time. Plan mixing, manpower, and staging before opening kits, and confirm all times against the current TDS.
| Condition | Typical value | Practical note |
|---|---|---|
| Recoat window | 1–2 hours | Recoat when firm enough to accept the next layer without damage |
| Light foot traffic | 3–4 hours | Protect from dirt, water, and early abuse |
| Vehicle traffic | About 24 hours | Allow longer in cool or damp conditions or at heavy film build |
| Full cure | 5–7 days | Delay aggressive cleaning and chemical exposure until full cure |
| Rain / moisture protection | 6–12 hours minimum | Protect exterior work during early cure |
Coverage and film build
Coverage is theoretical at the stated film thickness and assumes no application loss. The 2 US gal kit contains 7.56 L. Actual coverage is always lower, so allow for surface profile, porosity, texture, mixing residue, and application method when estimating quantities. Confirm coverage against the current TDS and project specification.
| Use mode | Typical film build | Theoretical coverage |
|---|---|---|
| Sealer / thin coat | 5–10 mils | Approximately 320–160 ft²/US gal (640–320 ft² per 2 gal kit) |
| Standard traffic coat | 10–20 mils | Approximately 160–80 ft²/US gal (320–160 ft² per 2 gal kit) |
| Heavy-duty coat | 20–30 mils | Approximately 80–53 ft²/US gal (160–105 ft² per 2 gal kit) |
| Broadcast seal coat | 8–20 mils | Depends on broadcast profile, aggregate size, and texture |
| Pigmented coat | 10–20 mils | Depends on colour, hiding, substrate profile, and backroll technique |
Application conditions
Confirm every condition against the current ResinTech TDS and project specification before use.
| Condition | Requirement |
|---|---|
| Substrate temperature | 10–30 °C |
| Ambient temperature | 10–32 °C |
| Relative humidity | Maximum 85% recommended |
| Dew point | Substrate at least 3 °C above dew point |
| Concrete moisture | Dry concrete; verify moisture before coating |
| Concrete age | Normally 28 days unless the designer approves earlier work |
| Minimum concrete strength | 3,600 psi compressive and 220 psi tensile pull-off |
Application notes
Always confirm application requirements against the current TDS, SDS, and project specification before use.
Surface preparation
Concrete must be sound, clean, dry, and free of laitance, curing compounds, sealers, oil, grease, and bond breakers. Mechanically prepare it to the surface profile required by the project. Thin coatings need a clean, uniform profile, while traffic and broadcast systems need a stronger mechanical tooth.
Vacuum until dust is removed from the profile and pores; do not coat dusty or contaminated concrete. Existing coatings must be sound, compatible, and properly abraded. Remove glossy, soft, unknown, or poorly bonded coatings.
Repair cracks, spalls, transitions, drains, and edges before coating. Moving joints must remain functional and be treated separately. Avoid application during falling slab temperature, when outgassing may cause bubbles or pinholes.
Mixing
Condition materials to the application temperature before use. Pre-mix Part A and Part B separately, adding compatible pigment to Part A where a pigmented coating is required. Combine Part A and Part B at a 1:1 ratio by weight and mix mechanically for two to three minutes at low speed.
Scrape the sides and bottom of the pail and mix until uniform. Avoid whipping air into the coating. Do not thin with solvents, and do not stretch the material beyond its recommended film build. Apply immediately after mixing. Polyaspartics cure quickly, so organize tools and crew before mixing.
Application and texture
Apply by squeegee and backroll, roller, brush for details, or spray where appropriate. Maintain a wet edge. For slip resistance, broadcast silica sand, quartz, aluminum oxide, or other approved media into the wet coating as specified.
When sealing decorative flake or quartz, use even pressure and avoid resin puddles that can change texture or gloss. For pigmented coats, use a consistent batch procedure and film thickness. Mock-ups are recommended for colour-sensitive work.
Stage traffic work to protect fresh coating from rain, condensation, dust, vehicle tires, and early turning stress.
Limitations
- HPP100 is not a crack-bridging membrane. Use a suitable flexible membrane such as FLEXCOAT-PU where movement or waterproofing is required.
- Do not apply to wet, frozen, contaminated, dusty, or condensing substrates.
- Moisture exposure during early cure may affect appearance, gloss, or surface quality.
- Excessive film thickness can affect cure and appearance; apply within the recommended thickness range.
- For maximum long-term abrasion or chemical resistance, use CRU as the premium protective topcoat where specified.
- Slip resistance depends on aggregate type, broadcast rate, topcoat thickness, and maintenance. Approve the texture through a mock-up.
Technical documentation
Request the current ResinTech HPP Technical Data Sheet and Safety Data Sheets from Canopus Supply before specifying or ordering. Confirm every value against the current TDS and SDS.
Trade purchasing note
All sales are intended for professional and trade purchasers. Before ordering, confirm product suitability, quantity, colour, system compatibility, substrate condition, pickup timing, and delivery requirements. Product use and installation are the responsibility of the purchaser and installer.
Technical information is provided for professional reference only. Product selection, substrate preparation, installation method, coverage, cure time, system compatibility, and final performance remain the responsibility of the purchaser, installer, project specifier, and/or manufacturer documentation. Always confirm suitability against the current TDS, SDS, project specification, and site conditions before use.
Order enquiries and volume orders
ResinTech does not sell this product directly through this website. Current pricing, stock, volume orders, system compatibility questions, pickup timing, and delivery across BC are handled by Canopus Supply.
- Call: 1 (250) 233-3000
- Email: order@canopussupply.com
- Pickup: Unit 103, 185 Forester Street, North Vancouver, BC
Canopus Supply Inc. is an authorized ResinTech distributor serving Metro Vancouver and British Columbia.